honda odyssey timing belt replacement procedure

fleckles March 07, 2022 honda , odyssey , procedure , replacement Comment

Remove timing belt covers. Temporarily fit crankshaft pulley 6.

Trouble Shooter Motor

I start with the hardest part crank pulley bolt and go.

. PARTS INFORMATION Coolant Type-2 2 gallons required. About Belt Replacement Timing Procedure Honda Odyssey. They both use the same timing belt kit though.

Are not part of timing belt job. See how to replace a timing belt on a Honda V6 J-Series engine specifically a 2000 Honda Odyssey. Check out your timing belt kit choices on Amazon.

Remove the timing belt idler pulley. Install the new tension rollers pay attention to the location of each one. Before positioning the new one you must take out all the tensioning rollers and the water pump.

Pay attention to the bolts you remove. Remove timing belt tensioner and idler pulleys. While 4th gen has a slightly different J35 Engine from 3rd gen the timing belt procedure is still the same and you can use same high quality Aisin TKH002 kit.

Lock camshafts as required and note position of camshaft timing marks. Replace the front camshaft the thrust cover the cam gear and the CMP sensor. Remove the covers from the timing belts.

Remove the front upper cover A rear upper cover B and lower cover C. Install the new distribution of your Honda Odyssey by respecting the markers. Remove the crankshaft pulley and the timing belt guide plate.

Remove the dipstick and tube A. Place the new water pump. Remove the engine intake upper cover and PCV hose.

Tension the belt as indicated by the manufacturers data. Remove the idler pulleys and tensioner for the timing belt. As needed lock the camshafts and take note of the position of the camshaft timing markers.

Remove the pulley from the crankshaft. If this not your first but is your first F motor belt be aware of the following. Ill show you what is actually involved when you have a timing belt replaced on your Honda Odyssey van and why it costs so much.

Timing belt replacement Honda Odyssey 1998-2004 35L V6 water pump too. Remove one of the battery clamp bolts from the battery tray and grind the end of it as shown. My video showing the basic steps in how to conduct your own timing belt replacement on a 3rd generation 2005-2010 Honda Odyssey minivan.

In this video we will replace a Honda 35L V6 Timing Belt Water Pump. Remove any items that are obstructing the removal of the timing belt covers. You need to put the pin in the back of the motor and make sure the balance shaft is aligned right.

Ensure belt is taut between crankshaft sprocket and camshaft sprocket. Up to 20 cash back Remove the side engine mount bracket. There are some different length ones in the timing cover.

If replacing the water pump do so at this time and of course drain the cooling system first. Allow tensioner to operate. I highly recommend the NAPA timing belt kits.

Fit timing belt in clockwise direction starting at crankshaft sprocket. Remove all accessories interfering with the removal of the timing belt covers. Remove the timing belt.

The vehicle that Im working on is a 2011 Pilot but the procedure is the same from th. Honda Odyssey Timing Belt Replacement Procedure. Slacken tensioner nut 10.

As it stands 3rd gen Ody had two types of serpentine belt tensioners based on the engine type A6 or A7. The repair information in this service bulletin is intended for Honda technicians who at a minimum have completed the first six Honda engine technical training courses including Timing Belt Replacement. Fit balancer shaft belt sprocket to crankshaft.

Discard the O-ring B. Be sure to like and subscrib. Remove the intake manifold bolts and nuts in three steps then remove the intake manifold.

BRAKE BOOSTER VACUUM HOSE EVAP CANISTER PURGE VALVE CONNECTOR WATER EVAP HOSE BYPASS HOSES THROTTLE BODY CONNECTOR POWER.

Wanted 1st Gen Timing Belt Replacement Procedure Honda Odyssey Forum

Toyota Honda Subaru Timing Belt Replacement Should The Idler Bearings Be Replaced At Same Time Proper Auto Repair Service